DTC Troubleshooting: P0137 (63)

DTC P0137:  Secondary HO2S (Sensor 2) Circuit Low Voltage


NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information.

1.Turn the ignition switch ON (II).

2.Clear the DTC with the HDS.

3.Start the engine. Hold the engine speed at 3,000 rpm (min-1) without load (in Park or neutral) until the radiator fan comes on, then let it idle.

4.Check the HO2S S2 in the DATA LIST with the HDS.

Does the voltage stay at 0.29 V or less?


YES - Go to 5.


NO - Intermittent failure, system is OK at this time.Check for poor connections or loose terminals at the secondary HO2S (Sensor 2) and the ECM/ PCM.n


5.Turn the ignition switch OFF.

6.Remove the center console.

7.Disconnect the secondary HO2S (Sensor 2) 4P connector.

8.Turn the ignition switch ON (II).

9.Check the HO2S S2 in the DATA LIST with the HDS.

Does the voltage stay at 0.29 V or less?


YES - Go to 10.


NO - Go to 14.


10.Turn the ignition switch OFF.

11.Jump the SCS line with the HDS.

12.Disconnect ECM/PCM connector C (44P).

13.Check for continuity between secondary HO2S (Sensor 2) 4P connector terminal No. 2 and body ground.

 

Is there continuity?


YES - Repair short in the wire between the ECM/PCM (C27) and the secondary HO2S (Sensor 2), then go to 16.


NO - Go to 24.


14.Turn the ignition switch OFF.

15.Replace the secondary HO2S (Sensor 2).

16.Reconnect all connectors.

17.Turn the ignition switch ON (II).

18.Reset the ECM/PCM with the HDS.

19.Do the ECM/PCM idle learn procedure.

20.Start the engine. Hold the engine speed at 3,000 rpm (min-1) without load (in Park or neutral) until the radiator fan comes on, then let it idle.

21.Test-drive under these conditions:
  • ECT SENSOR 1 above 80 °C (176 °F)
  • A/T in D position (M/T in 4th gear)
  • Engine speed between 1,500-3,000 rpm (min-1)
  • Drive about 1 minute or more

22.Check for Temporary DTCs or DTCs with the HDS.

Are any Temporary DTCs or DTCs indicated?


YES - If DTC P0137 is indicated, check for poor connections or loose terminals at the secondary HO2S (Sensor 2) and the ECM/PCM, then go to 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting.


NO - Go to 23.


23.Monitor the OBD STATUS for DTC P0137 in the DTCs MENU with the HDS.

Does the screen indicate PASSED?


YES - Troubleshooting is complete.n


NO - If the screen indicates FAILED, check for poor connections or loose terminals at the secondary HO2S (Sensor 2) and the ECM/PCM, then go to 1. If the screen indicates EXECUTING, keep driving until a result comes on. If the screen indicates OUT OF CONDITION, go to 20 and recheck.

24.Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM.

25.Start the engine. Hold the engine speed at 3,000 rpm (min-1) without load (in Park or neutral) until the radiator fan comes on, then let it idle.

26.Test-drive under these conditions:
  • ECT SENSOR 1 above 80 °C (176 °F)
  • A/T in D position (M/T in 4th gear)
  • Engine speed between 1,500-3,000 rpm (min-1)
  • Drive 1 minute or more

27.Check for Temporary DTCs or DTCs with the HDS.

Are any Temporary DTCs or DTCs indicated?


YES - If DTC P0137 is indicated, check for poor connections or loose terminals at the secondary HO2S (Sensor 2) and the ECM/PCM, then go to 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting.


NO - If the ECM/PCM was updated, troubleshooting is complete. If the ECM/PCM was substituted, replace the original ECM/PCM.n